How to Seat Tubeless Tire without Compressor | Step-by-Step

One of the most important things that a biker needs to learn is how to seat the tires for his or her bike. And if you are someone who uses a tubeless tire and doesn’t want to afford or have a compressor around you. Then knowing how to seat tubeless tire without compressor is a skill that you should prioritize the most.

In this article, we will break down every step that you will need to take in order to inflate a tubeless tire without the help of an air compressor. So, without further ado, let’s dive into the details, shall we?

How to Seat Tubeless Tire without Compressor

How to Inflate Tubeless Tire without Compressor: A Step-by-Step Guide

Here are the steps that you will need to follow in order to seat your bike’s tire without needing the help of a compressor of any kind. The steps are:

Step 1: Clean Your Wheel

This is one of the most important steps on seating a tire. But many seem to neglect or forget to do this entirely. By doing so, they mess up the entire seating process. As if there is dirt or any sort of dust or small stones lingering in the wheel while you apply saliant and the tire. Then you can be assured that you won’t be able to seat your tire at all.

What’s more, if this step is missed, it can lead to an unexpected and heavy tire blowout. And that is something we all want to avoid. So, clean your wheels properly when you start seating your tire.

After cleaning, make sure the fact that the wheels are dry before moving onto the next step.

Step 2: Inputting or Attaching the Valve in the Valve Stem

Most wheels come with their valve in the valve stem attached with them. If your wheels come with an added valve on the stem, then you can skip this step and move on to the next one. But for those who don’t have a valve attached to their wheels, start by deconstructing the valve.

Afterward, take the deconstructed valve and put it inside the valve stem. You will be able to see the valve’s lower body from the other side of the wheel. If so, then just reconstruct the valve by putting back the parts that you had removed earlier. Tighten the screws, and your valve stem is good to go.

Step 3: Install the Tire on the Right Direction

This is where many beginners make mistakes. First, roll out the tire so that it can get into its proper step. Then start installing it. To install it the right way, you need to keep the rotor on the left and ensure that the tire is going forward.

If your tire is facing the wrong way or going backward, then you will have to take it out and will need to do the process all over again. Also, make sure that the bead of the tire is on the outside of the wheel’s hole. Otherwise, the air won’t stay inside the tire at all.

So, make sure to be very cautious when installing the tire and ensure that both sides of the tire sitting in the center channel of the wheel. Once the installation is complete, proceed to the next step.

Step 4: Adding Sealant

Sealant is an important step as they will block up any holes or open spots left on your tire, which can cause the air to leak out. So, make sure you get the best sealant for your tire. You can contact your tire company to find out the best compatible one for your tire.

For an average tubeless tire, an amount between 30 millimeters to 60 millimeters is preferred. Put in the sealant 8 to 10 millimeters at a time around the tires. And as previously mentioned, ensure the fact that both sides of the tire are installed in the center channel of the wheel. An easy way to do this is just squeezing the tire all the way around.

Step 5: Seating the Rim of the Wheel

For many bikers, this is the most important step of seating a tire. Because there are a lot of things that can go wrong if you don’t know how to inflate a tire that won’t grab the rim. So, be very careful and follow this step precisely.

Grab your tire lever, and you are going to hook the bead and start pulling towards the edge of the wheel. Then you will hold your thumb right over the leaver on the tire and start to slide the tire leaver around. Once you start doing it, you will see that the tire is sitting right on the edge of the rim.

Try to slide at least half the way of the tire, as the more you reach towards the end, the resistance will get stronger. This will signal you that you are on the right path. Follow the same process on the other side of the tire as well.

Now, to pull out the tire lever, you are going to push with your thumb right next to the tire lever and pull the tire lever out. There will be a ‘ding’ sound when you do it.

Step 6: Start Pumping

Once you have seated the tire perfectly on the rim, all you have to do now is start pumping. So, grab your hand pump or floor pump, remove the valve core, connect the pump and start pumping.

Pump until you are satisfied but make sure that the tire is completely filled with air.

Step 7: Sealing off the Valve

To wrap everything up, put your hand under the valve and remove the pump. As soon as you remove the pump, put your thumb on the valve so only a minimal amount of air could escape and add your sealant. Then put back your valve core. Re-air up the tire a little bit. You should rotate the tire a bit so that the sealant can establish itself properly, and your tire should be ready.

And that’s it; these are the steps you need to know regarding how to inflate tubeless bike tire with a pump.

Conclusion

Changing bike tires is a necessary skill for every biker out there. As you won’t need a compressor for almost a year unless you change tires on a regular basis, then changing tires without a compressor is very important.

Now, if you have come this far in the article, then you already know how to seat tubeless tire without compressor. So, what are you waiting for? It’s time for you to seat your tire without a compressor. Best of luck!